Annual Pre-Holiday Savings Event It's finally here! Our 20th Annual Pre-Holiday 10% Savings Sale. During this long awaited sales event you can save 10% off everything in stock. Act now while stock is plentiful. Offer good on-line, or in our warehouse store. To receive your 10% Discount online customers must enter the Coupon Code - JINGLE129 in the promotional center section of the checkout page. To receive the discount in the store you must print this page or present the Pre-Holiday Sale postcard that was mailed to those of you on our mailing list. Sale in effect from November 1 through December 5, 2009 on all in-stock merchandise. Sorry NO Discounts on SUPER SAVER ITEMS, barrels or gift certificates. Offer can not be combined with any other offers or discounts of any kind. Backorders and special orders such as Limited Edition and Restricted Quantity Wine Kits and out of stock merchandise are not included. Shipping costs are not discounted. May not be applied towards previously purchased merchandise. 2009 Pre-Holiday Sale Information only   SKU: HOHO,  Ship Wt: 0.25 oz.      $0.00       QTY:

2 Pin Gas Connector These 2 PIn Gas Connectors are the pieces that connect to the keg posts. Our pin-lock models come in threaded ready to accept quick-disconnects. Quick Disconnects SOLD SEPARATELY 2 Pin Gas Connector   SKU: EQP53PG,  Ship Wt: 0.5 lb.      $8.95       QTY:          Quick Disconnect   SKU: EQP53QD,  Ship Wt: 2 oz.      $2.29       QTY:

3 Pin Liquid Connector These are the 3 Pin Liquid Connector pieces that connect to the keg posts. Our pin-lock models come in threaded ready to accept quick-disconnects. Quick Disconnects SOLD SEPARATELY 3 Pin Liquid Connector   SKU: EQP53PL,  Ship Wt: 0.5 lb.      $8.95       QTY:          Quick Disconnect   SKU: EQP53QD,  Ship Wt: 2 oz.      $2.29       QTY:

Aeration Stone Carbonates 5 gal keg in 15 minutes. Carbonating Stone with 1/4" barb: Carbonate your beer just like the pros. Simply attach one end a couple of feet of 1/4 inch tubing to the end of the dip tube inside of the keg, and the other end to The Stone. Make sure you attach hose clamps to both connections. Then set your regulator to about 2 psi, and the gas will be forced through the millions of tiny pores in the stone, which dissolves the gas into the liquid. Aeration Stone   SKU: EQP3133,  Ship Wt: 4 oz.      $34.95       QTY:

Air DIstribution Manifold - Three Way Run 3 kegs off one regulator, and have the safety of built in back check valves. Gives you the ability to shut off individual air lines and more control of air pressure in each line without disconnecting components of the system 3 Way Air DistributionManifold   SKU: EQP5305S,  Ship Wt: 2 lb.      $49.25       QTY:

Ball Lock Gas connector These Ball Lock Gas Connectors are the pieces that connect to the keg posts. Our ball-lock models come in threaded ready to accept quick-disconnects. Quick Disconnects SOLD SEPARATELYFor Homebrew Kegs. Ball Lock Gas connector   SKU: EQP53BG,  Ship Wt: 0.5 lb.      $8.95       QTY:

Ball Lock Liquid Connector These Ball Lock Liquid Connectors are the pieces that connect to the keg posts. Our ball-lock models come in threaded ready to accept quick-disconnects. Quick Disconnects SOLD SEPARATELYFor Homebrew Kegs. For Homebrew Kegs. Liquid Ball Lock Connector   SKU: EQP53BL,  Ship Wt: 0.5 lb.      $8.95       QTY:          Quick Disconnect   SKU: EQP53QD,  Ship Wt: 2 oz.      $2.29       QTY:

Ball lock O ring specify Ball lock O ring   SKU: EQP530B,  Ship Wt: 0.01 lb.      $0.59       QTY:

Ball Lock Poppet Valve replacement part for Ball lock Ball Lock Poppet Valve   SKU: EQP53BV,  Ship Wt: 0.2 lb.      $2.00       QTY:

Ball lock tank plug/gas replacement part for fittings Ball lock tank plug/gas   SKU: EQP5325,  Ship Wt: 0.5 lb.      $8.95       QTY:

Bronco Dispensing Pump Bronco Pump for dispensing draft beer. Compact in size, powerful in performance the Bronco Pump is full featured: Perfect for parties, picnics, social gatherings and holidays. You can enjoy the delights of real draught beer. Any Time—Anywhere: A portable party pump system for single valve kegs. This convenient pump system is compact in size and comes complete with a sturdy metal tapping base, high volume air pump, beer tubing and faucet. Lever action tapping Maximum air volume “ No Foam” pressure relief button Pressure Release Vent: This serves two purposes. First, it eliminates foaming caused by overpumping. Second, it allows the user to safely relieve pressure from the keg before removing the pump. Easy Cleaning: The pump can be quickly disassembled for cleaning. The pump body, tubing, and faucet can be immersed and rinsed in plain tap water. Bronco Pump - American   SKU: EQP5320P,  Ship Wt: 3 lb.      $59.79       QTY:

Cap O ring Replacement Fits homebrew keg cap. Small orings in picture not included but sold separately. O ring for Keg cap   SKU: EQP5312,  Ship Wt: 0.2 lb.      $4.10       QTY:

Carbonator valve coupling Attaches to plastic soda bottles. Use with your Regulator and Co2 tank to carbonate beer and soft drinks. Ball lock fitting. Simple and easy to use. Carbonator Valve coupling   SKU: EQP5317A,  Ship Wt: 1 lb.      $15.95       QTY:

Cleaning Brushes Nylon Bottle Brush for WINE, BEER Bottles and CARBOYS - Overall length of beer and wine bottle brush, 18 inches with a 3 inch x 6 inch nylon head brush. Carboy brush is 26 inches with a 3 inch x 6 inch X 6 inch white nylon head brush, loop end handle. Brushes for beer or wine bottles, carboys and kegging draw tubes. Carboy Brush   SKU: EQP3013,  Ship Wt: 8 oz.      $5.60       QTY:          Wine Bottle Brush   SKU: EQP3014,  Ship Wt: 8 oz.      $3.45       QTY:          Beer Bottle Brush   SKU: EQP3014B,  Ship Wt: 8 oz.      $2.95       QTY:          Keg Draw Tube Brush   SKU: EQP3014K,  Ship Wt: 8 oz.      $4.95       QTY:

CO2 Cartridges 16 Gram 16 gram CO2 cartridges. For use with HomeBrew Keg and Soda CO2 charger. 16 gram CO2 Cartridges EACH   SKU: EQP5298A,  Ship Wt: 4 oz.      $1.85       QTY:

CO2 Regulator Dual regulator. Lets you monitor inside pressure of beer and pressure on CO2 tank. This great regulator works with any Co2 Tank with a CGA-320 valve and measures PSI, as well as the volume of the Co2 gas in the Cylinder. The second gauge indicates how much Co2 is left in the cylinder and when it should be refilled. The screw in the center is used to adjust the output pressure. This double gauge regulator features a forged brass and die cast body for durability, accurate machining, molded nylon inslet seal, stainless steel valve seats for high corrosion resistance, stainless steel inlet filter, and a constant pressure supply at high output flow rates. The safety relief valve releases at 51-53 PSI. This regulator is also UL Listed. Primary Double Gauge Forged Brass Body Molded Nylon Inlet Seal Stainless Steel Valve Seats for Corrosion Resistance Stainless Steel Inlet Filter Constant Pressure Supply at High Output Flow Rates 0-60 PSI 3/8" O.D. Outlet Barb with Shut-Off Pressure Relief Valve releases at 51-53 PSI 3 Way Air Distribution Manifold    SKU: EQP5305S,  Ship Wt: 2 lb.      $45.25       QTY:          CO2 dual regulator   SKU: EQP5306,  Ship Wt: 2 lb.      $85.70       QTY:

CO2 Regulator Gauge Protector If your heavy CO2 cylinder falls, it can destroy the regulator gauges and knock your draft system out of commission. Protect your investment by installing an inexpensive gauge protector. Includes front and back rails, and three long screws. Fits our Cornelius regulator Regulator Cage   SKU: EQP5306C,  Ship Wt: 2 lb.      $9.85       QTY:

CO2 Tank CO2 tank for use with homebrew kegs. 5LB. Empty. Requires filling. CO2 Tank   SKU: EQP5305,  Ship Wt: 7 lb.      $110.82       QTY:

Cold Plate Cooler With 2 Faucets Cold Plate Cooler with 2 faucets complete with inlet and outlet fittings and faucets. This cooler box is for all commercial and home draft beer serving situations. Made of rugged, high impact plastic coolers with very durable exteriors. A perfect answers to your summer time picnic draft beer dispensing needs. A cold plate cooler is used in a party/special event environment to quickly chill warm beer to the ideal dispense temperature of 36-38°F. Dimensions 16" high x 24" long x 14" wide. *COLD PLATE COOLERS are recommended when the internal temperature of the draft beer keg can be maintained cooler than 55°F and will continuously dispense draft beer at 36°F. In a cold plate cooler, the beer is run through a aluminum cold plate that is covered with ice. The ice coming in contact with the plate causes the plate to become cold, which in turn causes the beer running through the plate to become cold. It is important to continuously drain the melted ice water from the cooler, and periodically push the ice down on the cold plate surface as it will occasionally bridge up and lose contact with the plate. Cold Plate Coolers 30-35 lbs. of applied pressure is recommended for dispensing beer that has an internal keg temperature of 50-55°F. A keg that is kept cold requires less applied pressure for dispensing. A keg that is being dispensed at room temperature or greater has a recommended applied pressure of 35-40 lbs. Use Tips · To prevent rinse water freeze during next function, dispense slight amount of beer through tubes before adding ice. - Fill cooler with crushed ice. - Continuously drain melted ice water from cooler. - Periodically push ice down on Cold Plate surface (ice will occasionally bridge up and lose contact with the plate). · 30-35 lbs. of applied pressure is recommended. This amount of pressure is required to dispense 50-55° F beer. Less pressure is needed with colder beer. CLEANING A few minutes of clean up will make the next party cooler event come together fast! · Always flush the beer out of the lines and clean after use before storing your party cooler. · Use a cleaner such as One Step designed for the beer industry. · Rinse thoroughly with water. · To prevent rinse water freeze during next function, dispense slight amount of beer through tubes before adding ice. **Additional fittings needed depending on type of keg. Cooler Cable needed for use with commercial kegs. Hexnut, Hosetail and 4 - 5 feet of 1/4" or 5/16" tubing needed for use with homebrew kegs. 1/4   SKU: EQP5307,  Ship Wt: 2 oz.      $0.31       QTY:          Hexnut & 1/4 Hosetail   SKU: EQP5319,  Ship Wt: 4 oz.      $5.95       QTY:          Cooler with 2 Faucets   SKU: EQP5335,  Ship Wt: 40 lb.      $325.00       QTY:          Beer Cooler Cable (1 for each commercial keg)   SKU: EQP5335A,  Ship Wt: 3 lb.      $9.25       QTY:

Complete Homebrew Kegging System 5 or 3 gallon keg, dual regulator, 5 lb Aluminum CO2 tank (empty)flex hose dispenser, and all connecting hardware. Reccomended additional equipment Aeration stone for quick carbonation. *NOTE Pictured with used keg. See photo of new keg below under Homebrew Keg. Aeration Stone   SKU: EQP3133,  Ship Wt: 4 oz.      $34.95       QTY:          5 gallon   SKU: EQP5301,  Ship Wt: 32 lb.      $373.50       QTY:          3 gallon   SKU: EQP5301B,  Ship Wt: 32 lb.      $391.50       QTY:          5 gallon with used keg   SKU: EQP5301U,  Ship Wt: 32 lb.      $265.75       QTY:

Counter pressure bottle filler Can be used with kegging Equipment only. Used when bottling beer after kegging Counter pressure bottle filler   SKU: EQP5316,  Ship Wt: 1 lb.      $67.50       QTY:

Diptube O-ring replacement part Dip tube O ring   SKU: EQP53DT,  Ship Wt: 0.01 lb.      $0.49       QTY:

Direct Keg Dispensing Unit Screws onto your threaded quick disconnect ball or pinlock. Complete Faucet set up for top dispensing. Includes Nickel coupling nut and faucet disconnect, faucet and handle. Direct Keg Dispenser Unit   SKU: EQP5332,  Ship Wt: 2 lb.      $41.95       QTY:

Faucet /Chrome Chrome Faucet for homebrew kegs. FAUCET ONLY Pictured with additional items: Handle, Socket Adapter, Shank Nut and Ball Lock Liquid Connector. Faucet only. Faucet Handle   SKU: EQP531H,  Ship Wt: 0.25 lb.      $3.60       QTY:          Socket Adapter   SKU: EQP5329,  Ship Wt: 0.2 lb.      $10.95       QTY:          Shank Nut   SKU: EQP5330,  Ship Wt: 0.2 lb.      $3.35       QTY:          Faucet/Chrome   SKU: EQP5331,  Ship Wt: 0.5 lb.      $25.25       QTY:          Ball Lock Liquid Connector   SKU: EQP53BL,  Ship Wt: 5 lb.      $8.95       QTY:

Faucet Handle Screw-ontype to fit chrome faucet. Faucet handle   SKU: EQP531H,  Ship Wt: 0.25 lb.      $3.60       QTY:

Faucet w/ shank 1/4 inch For converting your old fridge into a beertap system. Faucet handle not included Faucet w/shank 1/4"   SKU: EQP5318,  Ship Wt: 2 lb.      $44.00       QTY:

Gas Inlet Tube for kegs Gas Inlet tube   SKU: EQP53GIT,  Ship Wt: 0.2 lb.      $2.32       QTY:

Gas Line T Splitter/ Plastic for kegs Gas Line T Splitter/Plastic   SKU: EQP53GP,  Ship Wt: 0.2 lb.      $1.80       QTY:

Homebrew Keg - New The ease and convenience of kegging homebrewed beer and using CO2 to serve your homebrew can not be matched. Home brewers have been using kegs for years. The use of carbon dioxide gas to force carbonate the beer takes weeks off of the brewing process. New Kegs are 5 gallon capacity, dual handle, ball lock kegs with rubber tops and bottoms. Keg comes with ball lock fittings. 5 Gallon NEW   SKU: EQP5303,  Ship Wt: 31 lb.      $155.75       QTY:          3 gallon NEW   SKU: EQP530H,  Ship Wt: 10 lb.      $178.95       QTY:

Homebrew Keg - Used The ease and convenience of kegging homebrewed beer and using CO2 to serve your homebrew can not be matched. Home brewers have been using kegs for years. The use of carbon dioxide gas to force carbonate the beer takes weeks off of the brewing process. Used Kegs are 5 gallon capacity, dual handle, ball lock kegs with rubber tops and bottoms. They have been double pressure tested and have been cleaned but not sterilized. Kegs are guaranteed to hold pressure when you receive them. By pressure testing them we know that the existing relief valve and poppets do work. If you wish to totally rebuild the kegs you can purchase the relief valve and poppets separately. The kegs have minor scratches on the surface (all used kegs are scratched to some extent) however the scratches are purely cosmetic blemishes. They are functionally fine. 5 Gallon Used Keg    SKU: EQP5303U,  Ship Wt: 31 lb.      $38.95       QTY:

HomeBrew Keg and Soda CO2 charger Small & portable. Great for parties, beaches, boats, picnics, camping, cottages, etc.- great anywhere! Eliminates the need for cumbersome and costly Co2 tank and hoses. Completely controllable Co2 flow control trigger – with a touch of the finger! All brass inner valve parts will insure years of reliable service. Uses standard, inexpensive non-threaded 16 gram food-grade Co2 cartridges! The Co2 keeps beer fresh, and will not ‘skunk’ the beer flat like air from a hand pump. Convenient finger trigger allows for precise control of flow of the Co2 gas into the keg. Use with Quick Disconnect Gas-In Fittings (either ball lock or pin lock). 16 Gram CO2 cartridge EACH   SKU: EQP5298A,  Ship Wt: 4 oz.      $1.75       QTY:          Homebrew and Soda Co2 Charger   SKU: EQP5333,  Ship Wt: 1 lb.      $19.99       QTY:

Homebrew Refrigerator Conversion Kit Complete with ball lock disconnects, includes faucet,knob, shank, regulator Co2 tank (empty), hoses, fittings and stainless steel drip tray. (Keg not included) Homewbrew Refrigerator conversion kit   SKU: EQP5334,  Ship Wt: 20 lb.      $289.50       QTY:

Hose clamp small hose clamps for kegging fittings and tubing Hose Clamp   SKU: EQP5308,  Ship Wt: 0.3 lb.      $1.25       QTY:

Kegging Y (2 lines) splitter for multipal lines Kegging Y for 2 lines   SKU: EQP5313,  Ship Wt: 0.5 lb.      $6.80       QTY:

Misc . O Rings specify which one is needed Misc O Rings   SKU: EQP530M,  Ship Wt: 0.01 lb.      $0.25       QTY:

O2 Oxygenator System Experienced brewers know that oxygen-rich wort means healthy yeast cells, shorter lag phases, and faster fermentations. Adding pure oxygen to your wort is much more efficient than splashing or shaking a carboy full of beer. The O2 Oxygenation Kit includes instructions, a small Oxygen Regulator, Stainless Steel Diffusion Stone with 0.5 micron pores, and all the necessary Tubing. *(You provide a disposable oxygen cylinder, available at any hardware store.) O2 Oxygenation Kit   SKU: EQP3136,  Ship Wt: 2 lb.      $39.95       QTY:

Perlick Sankey Fast tap most popular, fits most american kegs Perlick Sanke Fast Tap DOMESTIC   SKU: EQP5320E,  Ship Wt: 2 lb.      $49.95       QTY:          Perlick Sanke Fast Tap EUROPEAN   SKU: EQP5320F,  Ship Wt: 2 lb.      $48.50       QTY:

Pin Lock O ring specify Pin lock O ring   SKU: EQP530P,  Ship Wt: 0.01 lb.      $0.59       QTY:

Pin Lock tank plug/2pin Gas replacement part for Pinlock Pinlock tank Plug/2pin Gas   SKU: EQP5327,  Ship Wt: 0.5 lb.      $27.95       QTY:

Pin Lock tank plug/3pin liquid replacement part for pin lock Pin Lock tank plug/3pin liquid   SKU: EQP5328,  Ship Wt: 0.5 lb.      $27.95       QTY:

Pinlock Poppet Valve Plug replacement part (Black) Pinlock Poppet Valve Plug   SKU: EQP53PV,  Ship Wt: 0.2 lb.      $2.39       QTY:

Pressure Relief Valve replacement part for caps with this valve Pressure Relief Valve   SKU: EQP5315,  Ship Wt: 0.2 lb.      $7.00       QTY:

Quick Disconnect Assembly This 2 part unit, can be used for quick disconnects on Ball or Pinlocks with threaded finish Quick Disconnect Assembly   SKU: EQP53QD,  Ship Wt: 0.2 lb.      $2.29       QTY:

Shank Nut/ Chrome fit end of shank to tighten Shank Nut/chrome   SKU: EQP5330,  Ship Wt: 0.2 lb.      $3.35       QTY:

Shut-off Air valve fits kegging Y and regulators Shut off Air Valve   SKU: EQP5314,  Ship Wt: 0.5 lb.      $9.80       QTY:

Silicone Spray 13 oz. for kegging lubrication or Resin type corks Silicone Spray   SKU: EQP53SS,  Ship Wt: 2 lb.      $10.95       QTY:

Socket adapter for plugs replacement part, fit ball or pin lock Socket adapter   SKU: EQP5329,  Ship Wt: 0.5 lb.      $10.95       QTY:

Squeeze Faucet plastic, used for dispensing Squeeze faucet   SKU: EQP5310,  Ship Wt: 0.25 lb.      $6.95       QTY:

Tap A Draft Repair Kit Includes a new pick up tube with stainless weight, bottle sealing O ring, and two C02 cartridge sealing O rings. Illustrated instructions are included to repair your Tap-A-Draft dispensing head. Tap A Draft Repair Kit   SKU: EQP5102A,  Ship Wt: 1 lb.      $12.50       QTY:

Tubing adapter 3/8X1/4 inch down or up size your tubing Tubing Adapter 3/8x1/4   SKU: EQP5311,  Ship Wt: 0.2 lb.      $1.80       QTY:

Tubing for kegs 1/4 inch This flexible food grade tubing is available in a variety of sizes. It is sold by the foot. Measurements are all inner diameter. Standard 1/4 tubing. 1/4" Tubing - per foot   SKU: EQP5307,  Ship Wt: 2 oz.      $0.31       QTY:

Universal Poppet Valve Plug replacement part (yellow) Universal Poppet Valve Plug   SKU: EQP53PU,  Ship Wt: 0.2 lb.      $6.75       QTY:

Washer for CO2 Regulator hard plastic Washer for CO2 Regulator   SKU: EQP5306W,  Ship Wt: 0.01 lb.      $0.25       QTY:

Washer/Hexnut/Hose tail please specify hosetail size Washer/Hexnut/Hosetail   SKU: EQP5319,  Ship Wt: 0.2 lb.      $5.95       QTY:

Wing nut fits shank, faucets, and regulators Wing Nut   SKU: EQP5321,  Ship Wt: 0.2 lb.      $3.95       QTY: